PT Boat Forum


Moderated by: Dick, Jeff D

The PT Boat Forum ª PT Boats of WWII ª  PT Boats - General

Page: 1 of 1

Back to Topic Index Page 209 | Replies: 1

 Author  Topic: Quanset Hut Facts
Rm2c Ron 16 PT 221

New Member
  

    
Post a Reply To This Topic    Reply With Quotes     Edit Message   Posted on: Mar 21, 2008 - 5:36am
The quonset hut, whose semi-cylindrical form was copied from the British Nissen hut, by the end of the war differed considerably in construction from its prototype. The original quonset hut was
framed with arch-rib members of steel, T sections, 2 inches by 2 inches by 1/4 inch. The hut was 16 feet by 36 feet in plan. The members were formed to a radius of 8 feet and covered with corrugated steel sheets, borne by wood purlins. The principal improvements over the Nissen type were an interior pressed wood lining, insulation, and a tongue-and-groove wood floor. Innumerable detail problems were encountered in the development of the original T-rib huts, principally because of the necessity for 48 different needs, such as galleys. shower-latrines, dental offices, isolation wards, and bakeries. Each type required individual drawings and layouts for the interior setup, and in many cases it was necessary to develop special interior equipment, such as special ovens and beds, to fit the quonset hut form. All huts were designed and detailed, using the original T- rib design.

The principal objection to this type of construction was that the curveline of the side walls began at the floor, resulting in a loss of effective width of the hut. A more suitable structural rib was found in the form of a welded strip steel member, 2 inches by 3 5/8 inches. This member--actually two light-weight channels welded back to back--contained a groove which held nails. The new rib was fabricated to provide a vertical sidewall, 4 feet high. This new hut was known as the quonset redesigned hut. Its floor plan was 16 feet by 36 feet. Standard-hut drawings were remade, for both structural and facility details. As the necessity arose for adapting the huts to use as dispensaries, latrines, hospitals, and other special facilities, the details were worked out and checked by actually erecting units in the field at the proving ground, to determine the practicability of the design for field use. In all, 86 approved interior layout plans were prepared for the small hut and the large 40-by-100-foot arch-rib warehouse.

To reduce shipping space and tonnage a redesign, incorporating lighter, corrugated, galvanized sheets for covering and half-inch plywood floors instead of one-inch tongue and groove, was effected. The new hut was larger, 20 feet by 48 feet, and lighter, using 3 tons of steel instead of 4 tons. It occupied from 270 to 325 cubic feet of shipping space instead of 450 cubic feet. The arch-rib again became semi-circular.

Toward the end of 1943, continuations to each end of the hut added 4-foot overhangs to the 48-foot length. The addition was to prevent driving rains and sunlight from entering the hut through the end bulkheads. The total outside length of the hut became 56 feet, but the actual interior living space remained 48 feet. The official quonset hut dimension nomenclature then became 20-by-56. However, in the spring of 1945, it was determined that the 4-foot overhangs on the huts used in northern or temperate climates were unnecessary, and they were eliminated. In order to standardize the nomenclature for both the northern and the tropical type the dimension nomenclature was changed back to 20-by-48. This. of course, was based on interior, living dimensions; the exterior dimensions of the tropical hut remained at 20-by-56. Throughout this war history, with few exceptions, when quonsets are referred to they are of the 20-by-48-foot living-space size.

As finally developed, the quonset hut required less shipping space than did tents with wood floors and frames, when equal numbers of men were to be accommodated.

Originally, all huts had unpainted galvanized exteriors. To reduce the chance of enemy observation from the air, an olive-drab camouflage paint was applied at the factory. After 1942 the factory service was extended to include packaging for overseas shipment. Before then, some plate bending, wood fabrication. and all packaging took place at Davisville.

The number of huts produced or procured by the Navy were as followed:

T-rib quonset 8,200
Quonset redesigned 25,000
Quonset 20-by-48 and 20-by-56 120,000
Total 153,200


Larger warehouse structures also were developed for Navy advance- base use. The first were 40-by-100-foot structures with vertical sides. They used 20 tons of steel and about 650 cubic feet of shipping space. About 300 of these were procured. They were superseded by a quonset-type warehouse of the same floor plan. The steel weight was 12 tons, and the shipping volume was 350 cubic feet. If a concrete floor was required, 600 additional cubic feet of shipping space was required for portland cement. In all, 11,800 such warehouses were procured. For large advance base supply functions, multiple arch-unit warehouses were developed from the 40-by-100-foot warehouses, to furnish greater storage area under single roofs.

Source: Building the Navy's Bases in World War II: History of the Bureau of Yards and Docks and the Civil Engineer Corps, 1940- 1946. Vol.1. Washington: Government Printing Office, 1947.




Total Posts: | Joined: Unregistered | IP Logged

Frank J Andruss Sr

TOP BOSS
  

    
Post a Reply To This Topic    Reply With Quotes     Edit Message     View Profile of Frank J Andruss Sr   Send Email To Frank J Andruss Sr Posted on: Mar 21, 2008 - 6:27am
RM

Thanks for the great information on the huts. It certainly is a valuable source for future use.


Total Posts: 3165 | Joined: Oct 9, 2006 - 6:09am | IP Logged


Lock Topic

 

Forum Legend

New Member

Reply to topic

More than 25 posts | Full Member

Reply to topic with quoted message

More than 50 posts | Advanced Member

Edit Message

More than 150 posts | MASTER

View profile

More than 300 posts | TOP BOSS

Email member