PT Boat Forum


Moderated by: Dick, Jeff D

The PT Boat Forum ª PT Boats of WWII ª  PT Boats - General

Page: 1 of 1

« Back to Topic Index Page 42 | Replies: 7

 Author  Topic: New Member Introduction- and a question
Deep Vee Forever

New Member
  

    
Post a Reply To This Topic    Reply With Quotes     Edit Message   Posted on: May 16, 2015 - 8:00pm
Hello, all-

Just poking my head in the door to say hello- my name is Randy Riker, and I'm new to the forum.
I've been a fan of PT boats ever since I was a kid, (I'm 51) and I'm currently building yet another Revell PT-109 kit (my sixth kit since the age of 10) and am currently doing lots of poking around here and there for additional details.

I have the 40th anniversary edition of Robert Donovan's book on PT-109 and 2 Squadron/Signal books on the 80' Elcos.

I've seen so many helpful hints and history being discussed here on the forum, but have one question. The decals in the Revell kit are so horribly inaccurate, and make me want to hurl, that I'm definitely not going to use them.
Is there a source for 1/72 scale decals for PT-103 class boats, that are the proper block-style numeric graphics, without shading, that JFK's boat had?
Unfortunately, I don't have an ALPS printer, or I'd probably make them myself.

Many thanks in advance for your assistance!

Randy

Total Posts: | Joined: Unregistered | IP Logged

TED WALTHER

TOP BOSS
  

    
Post a Reply To This Topic    Reply With Quotes     Edit Message     View Profile of TED WALTHER   Send Email To TED WALTHER Posted on: May 16, 2015 - 8:52pm
Randy;
Welcome, I always used model railroad lettering/numbers for my 1/72nd scale model PT's.
Take care,
TED


Total Posts: 3058 | Joined: Oct 16, 2006 - 7:42am | IP Logged

Deep Vee Forever

New Member
  

    
Post a Reply To This Topic    Reply With Quotes     Edit Message   Posted on: May 16, 2015 - 9:19pm
Thanks loads, Ted- both for the warm welcome and the tip- I'll check out some HO -scale decals at the local train shops here in Charlottesville- much obliged!

Randy

Randy

Total Posts: | Joined: Unregistered | IP Logged

Drew Cook

TOP BOSS
  

    
Post a Reply To This Topic    Reply With Quotes     Edit Message     View Profile of Drew Cook  Posted on: May 17, 2015 - 5:13am
Randy,

Welcome to the board.

We've got several WWII PT veterans, and many historians (amateur and otherwise), authors, enthusiasts and model-makers on this Forum. The old post archives alone are definitely worth your time to browse through.

The only decal on the Revell 1/72nd scale PT 109 model's decal sheet worth using is the smallest "109," which is the proper scale for the boat number 1) centered on the forward face of the charthouse between and above the ports, 2) on the port cockpit splash shield above the grab rail, 3) on the starboard twin-.50 turret below the turret rim, and 4) on the 20 mm pedestal .

Use this decal only if you want to represent an original factory marking, which may or may not have survived an over-painting/repainting in the forward area.

Vintage photographic evidence shows these original shaded numbers were preserved on some boats, sometimes carefully over-painted (with possibly gray replacing the too-high-visibility white), sometimes painted around, and sometimes not, replaced with several different font styles and even different colors.


Total Posts: 1306 | Joined: Oct 19, 2006 - 10:44am | IP Logged

Deep Vee Forever

New Member
  

    
Post a Reply To This Topic    Reply With Quotes     Edit Message   Posted on: May 17, 2015 - 10:20pm
Drew, thank you so much for the additional info regarding numbers and markings- most appreciated!

And you're right - the archived messages are a lot of fun to browse through

Thanks, again!

Randy

Total Posts: | Joined: Unregistered | IP Logged

Rick Abramson

New Member
  

    
Post a Reply To This Topic    Reply With Quotes     Edit Message     View Profile of Rick Abramson  Posted on: May 31, 2015 - 7:57pm
Randy:

For my Revell Elco's, I used Alliance Modelworks US Navy Ship Markings. They are 1:350 scale but in varying sizes.
Their stock number is NW35039.
Hope this helps.

Rick

Rick Abramson

Total Posts: 22 | Joined: Apr 21, 2015 - 4:30am | IP Logged

Rick Abramson

New Member
  

    
Post a Reply To This Topic    Reply With Quotes     Edit Message     View Profile of Rick Abramson  Posted on: May 31, 2015 - 8:04pm
Randy:

Their website is : http://www.am-works.com

Rick

Rick Abramson

Total Posts: 22 | Joined: Apr 21, 2015 - 4:30am | IP Logged

Deep Vee Forever

New Member
  

    
Post a Reply To This Topic    Reply With Quotes     Edit Message   Posted on: Jun 2, 2015 - 7:32pm
Rick- Thanks so much for the tip- I'll keep it in mind for future builds. I went to my local railroad hobby shop here in town and ordered a set of dry transfer markings in the proper block-style numerals, in white. The font style is called "U.S. Gothic Block" I'll get the manufacturer and product ID numbers and let everyone know as soon as I pick them up.

Thanks again!

Randy

Total Posts: | Joined: Unregistered | IP Logged


Lock Topic

 

Forum Legend

New Member

Reply to topic

More than 25 posts | Full Member

Reply to topic with quoted message

More than 50 posts | Advanced Member

Edit Message

More than 150 posts | MASTER

View profile

More than 300 posts | TOP BOSS

Email member