PT Boat Forum


Moderated by: Dick, Jeff D

The PT Boat Forum ª PT Boats of WWII ª  PT Boats - General

Page: 1 of 1

« Back to Topic Index Page 110 | Replies: 9

 Author  Topic: DONE! Finished Photos of My Italeri 1/35 PT-109
Phillip Gore

New Member
  

    
Post a Reply To This Topic    Reply With Quotes     Edit Message   Posted on: Jun 23, 2013 - 8:01pm
Fellow Modelers,

I was able to get several good overview photos, and they are below. My PT-109 took 263 hours to build over 3-1/2 months. Although I did make some modifications, I kept them to a minimum and tried to stay close to an “out of the box build”. In my opinion this kit builds into a great looking model straight out of the box. This project took a lot longer than expected, but I believe the large number of parts, and the required clean up really added to the hours. Italeri has produced a very good kit with great detail, but it is not on the same level of a Hasegawa, Tamiya or Wingnut Wings kit.

1st through 7th Image: One of the last modifications I made was using very thin styrene in place of the kit supplied photo-etch/clear cockpit windows. In the latest issue of Fine Scale Modeler magazine, this kit was built and reviewed. The reviewer stated that PT-109’s windscreen was replaced by armor plating before Kennedy assumed command. If this is true, then the modifications I made may be accurate. I hope you enjoy the photos and thanks for the support.
 photo 085_zps1e527cb0.jpg
 photo 086_zps3dcc64c9.jpg
 photo 088_zps1acc19c2.jpg
 photo 087_zpsc35d4d33.jpg
 photo 089_zpsd0038473.jpg
 photo 090_zps8c9414a2.jpg
 photo 0106_zps12bc62e6.jpg

Phillip


Total Posts: | Joined: Unregistered | IP Logged

Stuart Hurley

MASTER
  

    
Post a Reply To This Topic    Reply With Quotes     Edit Message     View Profile of Stuart Hurley  Posted on: Jun 24, 2013 - 2:04am
Phillip,
Really nice job, lovely shading and paint finish.


Best Regards,
Stu.





Total Posts: 255 | Joined: Mar 19, 2013 - 3:32am | IP Logged

  SteveS156

New Member
  

    
Post a Reply To This Topic    Reply With Quotes     Edit Message   Posted on: Jun 24, 2013 - 6:17am
Very nicely done! I particularly like the subtle shading.

Steve

SteveS156

Total Posts: | Joined: Unregistered | IP Logged

Frank Andruss

TOP BOSS
  

    
Post a Reply To This Topic    Reply With Quotes     Edit Message     View Profile of Frank Andruss   Send Email To Frank Andruss Posted on: Jun 24, 2013 - 4:44pm
Just beautiful, a wonderful model that would go in any Exhibit. It is of Museum quality.


Total Posts: 3964 | Joined: Feb 9, 2007 - 11:41am | IP Logged

David Waples

TOP BOSS
  

    
Post a Reply To This Topic    Reply With Quotes     Edit Message     View Profile of David Waples  Posted on: Jun 25, 2013 - 5:38am
Well done Phillip. Thanks again for sharing your work. I know it will be helpful to those wanting to do an out of the box model.
Dave

David Waples

Total Posts: 1679 | Joined: Jan 2, 2007 - 9:55pm | IP Logged

Roy Forbes

TOP BOSS
  

    
Post a Reply To This Topic    Reply With Quotes     Edit Message     View Profile of Roy Forbes  Posted on: Jun 25, 2013 - 8:03am
Really nice job Phillip. I like the way she looks in the different color you chose getting away from the familiar olive tones. I also like the light weathering you did that takes her beyond the factory look but not way over the top. I enjoyed watching your build. What's next?


Total Posts: 371 | Joined: Sep 5, 2012 - 4:57pm | IP Logged

victorkchun

New Member
  

    
Post a Reply To This Topic    Reply With Quotes     Edit Message   Posted on: Jun 26, 2013 - 10:12am
Hi Philip,
Since you mentioned all four top model companies, I sure like to see finished PT models made
by them on massage board for comparison.
Victor

Victor K Chun

Total Posts: | Joined: Unregistered | IP Logged

PeterTareBuilder2

MASTER
  

    
Post a Reply To This Topic    Reply With Quotes     Edit Message     View Profile of PeterTareBuilder2  Posted on: Jun 26, 2013 - 1:51pm
Hi Phillip.

Nice build. I think I might get one of these for a radio controlled model.

You said, "...but it is not on the same level of a Hasegawa, Tamiya or Wingnut Wings kit". I dread to think what any of those three companies would have charge for a 1/35 scale PT boat model. I say that after looking at the cost of Tamiya's recent 1/35 scale armour kits or the 1/32 scale aircraft kits.

Even the 596 kit is a great deal when you consider that an Italeri 40mm Bofors gun is about 1/3 the cost of the entire 596 kit.

Yes, the more I see this 109 model kit built the more I think I'll get one.

Cheers from Peter


"Give me a fast boat for we want to get out of harm's way too."

Total Posts: 204 | Joined: Dec 8, 2012 - 6:03pm | IP Logged

Kornbeef

New Member
  

    
Post a Reply To This Topic    Reply With Quotes     Edit Message   Posted on: Jun 27, 2013 - 6:49am
Lovely build Phillip. Quite inspiring. Once I get my PT490 finished I may have to nab one of these earlier boats.

I hope my build turns out half as nice. Actually got some good points from studying your pics as to what some of the blobs on pics of PT490 might actually be.

Thanks for sharing.

Keith



Never to old to learn something
Doesn't stop me forgetting the obvious though

Total Posts: | Joined: Unregistered | IP Logged

Drew Cook

TOP BOSS
  

    
Post a Reply To This Topic    Reply With Quotes     Edit Message     View Profile of Drew Cook  Posted on: Jun 28, 2013 - 9:46am
Very nice, Phil. A great-looking model, and thanks for posting photos of it.

As to the 109's plexiglass windshield, I personally think it was more likely it was painted over than replaced with armor plating, but...these types of suppositions are endless.


Total Posts: 1306 | Joined: Oct 19, 2006 - 10:44am | IP Logged


Lock Topic

 

Forum Legend

New Member

Reply to topic

More than 25 posts | Full Member

Reply to topic with quoted message

More than 50 posts | Advanced Member

Edit Message

More than 150 posts | MASTER

View profile

More than 300 posts | TOP BOSS

Email member